Merge branch 'master' into mmicko/efinix

tests/anlogic/.gitignore

@@ -0,0 +1,4 @@
+*.log
+/run-test.mk
++*_synth.v
++*_testbench

tests/anlogic/add_sub.v

@@ -0,0 +1,13 @@
+module top
+(
+ input [3:0] x,
+ input [3:0] y,
+
+ output [3:0] A,
+ output [3:0] B
+ );
+
+assign A =  x + y;
+assign B =  x - y;
+
+endmodule

tests/anlogic/add_sub.ys

@@ -0,0 +1,10 @@
+read_verilog add_sub.v
+hierarchy -top top
+proc
+equiv_opt -assert -map +/anlogic/cells_sim.v synth_anlogic # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd top # Constrain all select calls below inside the top module
+select -assert-count 10 t:AL_MAP_ADDER
+select -assert-count 4 t:AL_MAP_LUT1
+
+select -assert-none t:AL_MAP_LUT1 t:AL_MAP_ADDER %% t:* %D

tests/anlogic/counter.v

@@ -0,0 +1,17 @@
+module top    (
+out,
+clk,
+reset
+);
+    output [7:0] out;
+    input clk, reset;
+    reg [7:0] out;
+
+    always @(posedge clk, posedge reset)
+		if (reset) begin
+			out <= 8'b0 ;
+		end else
+			out <= out + 1;
+
+
+endmodule

tests/anlogic/counter.ys

@@ -0,0 +1,11 @@
+read_verilog counter.v
+hierarchy -top top
+proc
+flatten
+equiv_opt -map +/anlogic/cells_sim.v synth_anlogic # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd top # Constrain all select calls below inside the top module
+
+select -assert-count 9 t:AL_MAP_ADDER
+select -assert-count 8 t:AL_MAP_SEQ
+select -assert-none t:AL_MAP_SEQ t:AL_MAP_ADDER %% t:* %D

tests/anlogic/dffs.v

@@ -0,0 +1,15 @@
+module dff
+    ( input d, clk, output reg q );
+	always @( posedge clk )
+            q <= d;
+endmodule
+
+module dffe
+    ( input d, clk, en, output reg q );
+    initial begin
+      q = 0;
+    end
+	always @( posedge clk )
+		if ( en )
+			q <= d;
+endmodule

tests/anlogic/dffs.ys

@@ -0,0 +1,20 @@
+read_verilog dffs.v
+design -save read
+
+hierarchy -top dff
+proc
+equiv_opt -assert -map +/anlogic/cells_sim.v synth_anlogic # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd dff # Constrain all select calls below inside the top module
+select -assert-count 1 t:AL_MAP_SEQ
+select -assert-none t:AL_MAP_SEQ %% t:* %D
+
+design -load read
+hierarchy -top dffe
+proc
+equiv_opt -assert -map +/anlogic/cells_sim.v synth_anlogic # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd dffe # Constrain all select calls below inside the top module
+select -assert-count 1 t:AL_MAP_LUT3
+select -assert-count 1 t:AL_MAP_SEQ
+select -assert-none t:AL_MAP_LUT3 t:AL_MAP_SEQ %% t:* %D

tests/anlogic/fsm.v

@@ -0,0 +1,55 @@
+ module fsm (
+ clock,
+ reset,
+ req_0,
+ req_1,
+ gnt_0,
+ gnt_1
+ );
+ input   clock,reset,req_0,req_1;
+ output  gnt_0,gnt_1;
+ wire    clock,reset,req_0,req_1;
+ reg     gnt_0,gnt_1;
+
+ parameter SIZE = 3           ;
+ parameter IDLE  = 3'b001,GNT0 = 3'b010,GNT1 = 3'b100,GNT2 = 3'b101 ;
+
+ reg [SIZE-1:0] state;
+ reg [SIZE-1:0] next_state;
+
+ always @ (posedge clock)
+ begin : FSM
+ if (reset == 1'b1) begin
+   state <=  #1  IDLE;
+   gnt_0 <= 0;
+   gnt_1 <= 0;
+ end else
+  case(state)
+    IDLE : if (req_0 == 1'b1) begin
+                 state <=  #1  GNT0;
+                 gnt_0 <= 1;
+               end else if (req_1 == 1'b1) begin
+                 gnt_1 <= 1;
+                 state <=  #1  GNT0;
+               end else begin
+                 state <=  #1  IDLE;
+               end
+    GNT0 : if (req_0 == 1'b1) begin
+                 state <=  #1  GNT0;
+               end else begin
+                 gnt_0 <= 0;
+                 state <=  #1  IDLE;
+               end
+    GNT1 : if (req_1 == 1'b1) begin
+                 state <=  #1  GNT2;
+				 gnt_1 <= req_0;
+               end
+    GNT2 : if (req_0 == 1'b1) begin
+                 state <=  #1  GNT1;
+				 gnt_1 <= req_1;
+               end
+    default : state <=  #1  IDLE;
+ endcase
+ end
+
+endmodule

tests/anlogic/fsm.ys

@@ -0,0 +1,15 @@
+read_verilog fsm.v
+hierarchy -top fsm
+proc
+#flatten
+#ERROR: Found 4 unproven $equiv cells in 'equiv_status -assert'.
+#equiv_opt -assert -map +/anlogic/cells_sim.v synth_anlogic # equivalency check
+equiv_opt -map +/anlogic/cells_sim.v synth_anlogic # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd fsm # Constrain all select calls below inside the top module
+select -assert-count 1 t:AL_MAP_LUT2
+select -assert-count 5 t:AL_MAP_LUT5
+select -assert-count 1 t:AL_MAP_LUT6
+select -assert-count 6 t:AL_MAP_SEQ
+
+select -assert-none t:AL_MAP_LUT2 t:AL_MAP_LUT5 t:AL_MAP_LUT6 t:AL_MAP_SEQ %% t:* %D

tests/anlogic/latches.v

@@ -0,0 +1,24 @@
+module latchp
+    ( input d, clk, en, output reg q );
+	always @*
+		if ( en )
+			q <= d;
+endmodule
+
+module latchn
+    ( input d, clk, en, output reg q );
+	always @*
+		if ( !en )
+			q <= d;
+endmodule
+
+module latchsr
+    ( input d, clk, en, clr, pre, output reg q );
+	always @*
+		if ( clr )
+			q <= 1'b0;
+		else if ( pre )
+			q <= 1'b1;
+		else if ( en )
+			q <= d;
+endmodule

tests/anlogic/latches.ys

@@ -0,0 +1,33 @@
+read_verilog latches.v
+design -save read
+
+hierarchy -top latchp
+proc
+# Can't run any sort of equivalence check because latches are blown to LUTs
+synth_anlogic
+cd latchp # Constrain all select calls below inside the top module
+select -assert-count 1 t:AL_MAP_LUT3
+
+select -assert-none t:AL_MAP_LUT3 %% t:* %D
+
+
+design -load read
+hierarchy -top latchn
+proc
+# Can't run any sort of equivalence check because latches are blown to LUTs
+synth_anlogic
+cd latchn # Constrain all select calls below inside the top module
+select -assert-count 1 t:AL_MAP_LUT3
+
+select -assert-none t:AL_MAP_LUT3 %% t:* %D
+
+
+design -load read
+hierarchy -top latchsr
+proc
+# Can't run any sort of equivalence check because latches are blown to LUTs
+synth_anlogic
+cd latchsr # Constrain all select calls below inside the top module
+select -assert-count 1 t:AL_MAP_LUT5
+
+select -assert-none t:AL_MAP_LUT5 %% t:* %D

tests/anlogic/memory.v

@@ -0,0 +1,21 @@
+module top
+(
+	input [7:0] data_a,
+	input [6:1] addr_a,
+	input we_a, clk,
+	output reg [7:0] q_a
+);
+	// Declare the RAM variable
+	reg [7:0] ram[63:0];
+
+	// Port A
+	always @ (posedge clk)
+	begin
+		if (we_a)
+		begin
+			ram[addr_a] <= data_a;
+			q_a <= data_a;
+		end
+		q_a <= ram[addr_a];
+	end
+endmodule

tests/anlogic/memory.ys

@@ -0,0 +1,21 @@
+read_verilog memory.v
+hierarchy -top top
+proc
+memory -nomap
+equiv_opt -run :prove -map +/anlogic/cells_sim.v synth_anlogic
+memory
+opt -full
+
+miter -equiv -flatten -make_assert -make_outputs gold gate miter
+#ERROR: Failed to import cell gate.mem.0.0.0 (type EG_LOGIC_DRAM16X4) to SAT database.
+#sat -verify -prove-asserts -seq 3 -set-init-zero -show-inputs -show-outputs miter
+
+design -load postopt
+cd top
+
+select -assert-count 8  t:AL_MAP_LUT2
+select -assert-count 8  t:AL_MAP_LUT4
+select -assert-count 8   t:AL_MAP_LUT5
+select -assert-count 36 t:AL_MAP_SEQ
+select -assert-count 8  t:EG_LOGIC_DRAM16X4 #Why not AL_LOGIC_BRAM?
+select -assert-none t:AL_MAP_LUT2 t:AL_MAP_LUT4 t:AL_MAP_LUT5 t:AL_MAP_SEQ t:EG_LOGIC_DRAM16X4 %% t:* %D

tests/anlogic/mux.v

@@ -0,0 +1,65 @@
+module mux2 (S,A,B,Y);
+    input S;
+    input A,B;
+    output reg Y;
+
+    always @(*)
+		Y = (S)? B : A;
+endmodule
+
+module mux4 ( S, D, Y );
+
+input[1:0] S;
+input[3:0] D;
+output Y;
+
+reg Y;
+wire[1:0] S;
+wire[3:0] D;
+
+always @*
+begin
+    case( S )
+       0 : Y = D[0];
+       1 : Y = D[1];
+       2 : Y = D[2];
+       3 : Y = D[3];
+   endcase
+end
+
+endmodule
+
+module mux8 ( S, D, Y );
+
+input[2:0] S;
+input[7:0] D;
+output Y;
+
+reg Y;
+wire[2:0] S;
+wire[7:0] D;
+
+always @*
+begin
+   case( S )
+       0 : Y = D[0];
+       1 : Y = D[1];
+       2 : Y = D[2];
+       3 : Y = D[3];
+       4 : Y = D[4];
+       5 : Y = D[5];
+       6 : Y = D[6];
+       7 : Y = D[7];
+   endcase
+end
+
+endmodule
+
+module mux16 (D, S, Y);
+ 	input  [15:0] D;
+ 	input  [3:0] S;
+ 	output Y;
+
+assign Y = D[S];
+
+endmodule

tests/anlogic/mux.ys

@@ -0,0 +1,42 @@
+read_verilog mux.v
+design -save read
+
+hierarchy -top mux2
+proc
+equiv_opt -assert -map +/anlogic/cells_sim.v synth_anlogic # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd mux2 # Constrain all select calls below inside the top module
+select -assert-count 1 t:AL_MAP_LUT3
+
+select -assert-none t:AL_MAP_LUT3 %% t:* %D
+
+design -load read
+hierarchy -top mux4
+proc
+equiv_opt -assert -map +/anlogic/cells_sim.v synth_anlogic # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd mux4 # Constrain all select calls below inside the top module
+select -assert-count 1 t:AL_MAP_LUT6
+
+select -assert-none t:AL_MAP_LUT6 %% t:* %D
+
+design -load read
+hierarchy -top mux8
+proc
+equiv_opt -assert -map +/anlogic/cells_sim.v synth_anlogic # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd mux8 # Constrain all select calls below inside the top module
+select -assert-count 3 t:AL_MAP_LUT4
+select -assert-count 1 t:AL_MAP_LUT6
+
+select -assert-none t:AL_MAP_LUT4 t:AL_MAP_LUT6 %% t:* %D
+
+design -load read
+hierarchy -top mux16
+proc
+equiv_opt -assert -map +/anlogic/cells_sim.v synth_anlogic # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd mux16 # Constrain all select calls below inside the top module
+select -assert-count 5 t:AL_MAP_LUT6
+
+select -assert-none t:AL_MAP_LUT6 %% t:* %D

tests/anlogic/run-test.sh

@@ -0,0 +1,20 @@
+#!/usr/bin/env bash
+set -e
+{
+echo "all::"
+for x in *.ys; do
+	echo "all:: run-$x"
+	echo "run-$x:"
+	echo "	@echo 'Running $x..'"
+	echo "	@../../yosys -ql ${x%.ys}.log -w 'Yosys has only limited support for tri-state logic at the moment.' $x"
+done
+for s in *.sh; do
+	if [ "$s" != "run-test.sh" ]; then
+		echo "all:: run-$s"
+		echo "run-$s:"
+		echo "	@echo 'Running $s..'"
+		echo "	@bash $s"
+	fi
+done
+} > run-test.mk
+exec ${MAKE:-make} -f run-test.mk

tests/anlogic/shifter.v

@@ -0,0 +1,16 @@
+module top    (
+out,
+clk,
+in
+);
+    output [7:0] out;
+    input signed clk, in;
+    reg signed [7:0] out = 0;
+
+    always @(posedge clk)
+	begin
+		out    <= out >> 1;
+		out[7] <= in;
+	end
+
+endmodule

tests/anlogic/shifter.ys

@@ -0,0 +1,10 @@
+read_verilog shifter.v
+hierarchy -top top
+proc
+flatten
+equiv_opt -assert -map +/anlogic/cells_sim.v synth_anlogic # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd top # Constrain all select calls below inside the top module
+select -assert-count 8 t:AL_MAP_SEQ
+
+select -assert-none t:AL_MAP_SEQ %% t:* %D

tests/anlogic/tribuf.v

@@ -0,0 +1,8 @@
+module tristate (en, i, o);
+    input en;
+    input i;
+    output o;
+
+	assign o = en ? i : 1'bz;
+
+endmodule

tests/anlogic/tribuf.ys

@@ -0,0 +1,9 @@
+read_verilog tribuf.v
+hierarchy -top tristate
+proc
+flatten
+equiv_opt -assert -map +/anlogic/cells_sim.v -map +/simcells.v synth_anlogic # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd tristate # Constrain all select calls below inside the top module
+select -assert-count 1 t:$_TBUF_
+select -assert-none t:$_TBUF_ %% t:* %D

tests/ecp5/.gitignore

@@ -0,0 +1,2 @@
+*.log
+/run-test.mk

tests/ecp5/add_sub.v

@@ -0,0 +1,13 @@
+module top
+(
+ input [3:0] x,
+ input [3:0] y,
+
+ output [3:0] A,
+ output [3:0] B
+ );
+
+assign A =  x + y;
+assign B =  x - y;
+
+endmodule

tests/ecp5/add_sub.ys

@@ -0,0 +1,9 @@
+read_verilog add_sub.v
+hierarchy -top top
+proc
+equiv_opt -assert -map +/ecp5/cells_sim.v synth_ecp5 # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd top # Constrain all select calls below inside the top module
+select -assert-count 10 t:LUT4
+select -assert-none t:LUT4 %% t:* %D
+

tests/ecp5/adffs.v

@@ -0,0 +1,47 @@
+module adff
+    ( input d, clk, clr, output reg q );
+    initial begin
+      q = 0;
+    end
+	always @( posedge clk, posedge clr )
+		if ( clr )
+			q <= 1'b0;
+		else
+            q <= d;
+endmodule
+
+module adffn
+    ( input d, clk, clr, output reg q );
+    initial begin
+      q = 0;
+    end
+	always @( posedge clk, negedge clr )
+		if ( !clr )
+			q <= 1'b0;
+		else
+            q <= d;
+endmodule
+
+module dffs
+    ( input d, clk, pre, clr, output reg q );
+    initial begin
+      q = 0;
+    end
+	always @( posedge clk )
+		if ( pre )
+			q <= 1'b1;
+		else
+            q <= d;
+endmodule
+
+module ndffnr
+    ( input d, clk, pre, clr, output reg q );
+    initial begin
+      q = 0;
+    end
+	always @( negedge clk )
+		if ( !clr )
+			q <= 1'b0;
+		else
+            q <= d;
+endmodule

tests/ecp5/adffs.ys

@@ -0,0 +1,40 @@
+read_verilog adffs.v
+design -save read
+
+hierarchy -top adff
+proc
+equiv_opt -assert -map +/ecp5/cells_sim.v synth_ecp5 # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd adff # Constrain all select calls below inside the top module
+select -assert-count 1 t:TRELLIS_FF
+select -assert-none t:TRELLIS_FF %% t:* %D
+
+design -load read
+hierarchy -top adffn
+proc
+equiv_opt -assert -map +/ecp5/cells_sim.v synth_ecp5 # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd adffn # Constrain all select calls below inside the top module
+select -assert-count 1 t:TRELLIS_FF
+select -assert-count 1 t:LUT4
+select -assert-none t:TRELLIS_FF t:LUT4 %% t:* %D
+
+design -load read
+hierarchy -top dffs
+proc
+equiv_opt -assert -map +/ecp5/cells_sim.v synth_ecp5 # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd dffs # Constrain all select calls below inside the top module
+select -assert-count 1 t:TRELLIS_FF
+select -assert-count 1 t:LUT4
+select -assert-none t:TRELLIS_FF t:LUT4 %% t:* %D
+
+design -load read
+hierarchy -top ndffnr
+proc
+equiv_opt -assert -map +/ecp5/cells_sim.v synth_ecp5 # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd ndffnr # Constrain all select calls below inside the top module
+select -assert-count 1 t:TRELLIS_FF
+select -assert-count 1 t:LUT4
+select -assert-none t:TRELLIS_FF t:LUT4 %% t:* %D

tests/ecp5/counter.v

@@ -0,0 +1,17 @@
+module top    (
+out,
+clk,
+reset
+);
+    output [7:0] out;
+    input clk, reset;
+    reg [7:0] out;
+
+    always @(posedge clk, posedge reset)
+		if (reset) begin
+			out <= 8'b0 ;
+		end else
+			out <= out + 1;
+
+
+endmodule

tests/ecp5/counter.ys

@@ -0,0 +1,10 @@
+read_verilog counter.v
+hierarchy -top top
+proc
+flatten
+equiv_opt -map +/ecp5/cells_sim.v synth_ecp5 # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd top # Constrain all select calls below inside the top module
+select -assert-count 4 t:CCU2C
+select -assert-count 8 t:TRELLIS_FF
+select -assert-none t:CCU2C t:TRELLIS_FF %% t:* %D

tests/ecp5/dffs.v

@@ -0,0 +1,15 @@
+module dff
+    ( input d, clk, output reg q );
+	always @( posedge clk )
+            q <= d;
+endmodule
+
+module dffe
+    ( input d, clk, en, output reg q );
+    initial begin
+      q = 0;
+    end
+	always @( posedge clk )
+		if ( en )
+			q <= d;
+endmodule

tests/ecp5/dffs.ys

@@ -0,0 +1,19 @@
+read_verilog dffs.v
+design -save read
+
+hierarchy -top dff
+proc
+equiv_opt -assert -map +/ecp5/cells_sim.v synth_ecp5 # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd dff # Constrain all select calls below inside the top module
+select -assert-count 1 t:TRELLIS_FF
+select -assert-none t:TRELLIS_FF %% t:* %D
+
+design -load read
+hierarchy -top dffe
+proc
+equiv_opt -assert -map +/ecp5/cells_sim.v synth_ecp5 # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd dffe # Constrain all select calls below inside the top module
+select -assert-count 1 t:TRELLIS_FF
+select -assert-none t:TRELLIS_FF %% t:* %D

tests/ecp5/dpram.v

@@ -0,0 +1,23 @@
+/*
+Example from: https://www.latticesemi.com/-/media/LatticeSemi/Documents/UserManuals/EI/iCEcube201701UserGuide.ashx?document_id=52071 [p. 72].
+*/
+module top (din, write_en, waddr, wclk, raddr, rclk, dout);
+parameter addr_width = 8;
+parameter data_width = 8;
+input [addr_width-1:0] waddr, raddr;
+input [data_width-1:0] din;
+input write_en, wclk, rclk;
+output [data_width-1:0] dout;
+reg [data_width-1:0] dout;
+reg [data_width-1:0] mem [(1<<addr_width)-1:0]
+/* synthesis syn_ramstyle = "no_rw_check" */ ;
+always @(posedge wclk) // Write memory.
+begin
+if (write_en)
+mem[waddr] <= din; // Using write address bus.
+end
+always @(posedge rclk) // Read memory.
+begin
+dout <= mem[raddr]; // Using read address bus.
+end
+endmodule

tests/ecp5/dpram.ys

@@ -0,0 +1,18 @@
+read_verilog dpram.v
+hierarchy -top top
+proc
+memory -nomap
+equiv_opt -run :prove -map +/ecp5/cells_sim.v synth_ecp5
+memory
+opt -full
+
+miter -equiv -flatten -make_assert -make_outputs gold gate miter
+
+#Blocked by issue #1358 (Missing ECP5 simulation models)
+#ERROR: Failed to import cell gate.mem.0.0.0 (type DP16KD) to SAT database.
+#sat -verify -prove-asserts -seq 3 -set-init-zero -show-inputs -show-outputs miter
+
+design -load postopt
+cd top
+select -assert-count 1 t:DP16KD
+select -assert-none t:DP16KD %% t:* %D

tests/ecp5/fsm.v

@@ -0,0 +1,55 @@
+ module fsm (
+ clock,
+ reset,
+ req_0,
+ req_1,
+ gnt_0,
+ gnt_1
+ );
+ input   clock,reset,req_0,req_1;
+ output  gnt_0,gnt_1;
+ wire    clock,reset,req_0,req_1;
+ reg     gnt_0,gnt_1;
+
+ parameter SIZE = 3           ;
+ parameter IDLE  = 3'b001,GNT0 = 3'b010,GNT1 = 3'b100,GNT2 = 3'b101 ;
+
+ reg [SIZE-1:0] state;
+ reg [SIZE-1:0] next_state;
+
+ always @ (posedge clock)
+ begin : FSM
+ if (reset == 1'b1) begin
+   state <=  #1  IDLE;
+   gnt_0 <= 0;
+   gnt_1 <= 0;
+ end else
+  case(state)
+    IDLE : if (req_0 == 1'b1) begin
+                 state <=  #1  GNT0;
+                 gnt_0 <= 1;
+               end else if (req_1 == 1'b1) begin
+                 gnt_1 <= 1;
+                 state <=  #1  GNT0;
+               end else begin
+                 state <=  #1  IDLE;
+               end
+    GNT0 : if (req_0 == 1'b1) begin
+                 state <=  #1  GNT0;
+               end else begin
+                 gnt_0 <= 0;
+                 state <=  #1  IDLE;
+               end
+    GNT1 : if (req_1 == 1'b1) begin
+                 state <=  #1  GNT2;
+				 gnt_1 <= req_0;
+               end
+    GNT2 : if (req_0 == 1'b1) begin
+                 state <=  #1  GNT1;
+				 gnt_1 <= req_1;
+               end
+    default : state <=  #1  IDLE;
+ endcase
+ end
+
+endmodule

tests/ecp5/fsm.ys

@@ -0,0 +1,12 @@
+read_verilog fsm.v
+hierarchy -top fsm
+proc
+flatten
+equiv_opt -assert -map +/ecp5/cells_sim.v synth_ecp5 # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd fsm # Constrain all select calls below inside the top module
+select -assert-count 1 t:L6MUX21
+select -assert-count 13 t:LUT4
+select -assert-count 5 t:PFUMX
+select -assert-count 5 t:TRELLIS_FF
+select -assert-none t:L6MUX21 t:LUT4 t:PFUMX t:TRELLIS_FF %% t:* %D

tests/ecp5/latches.v

@@ -0,0 +1,24 @@
+module latchp
+    ( input d, clk, en, output reg q );
+	always @*
+		if ( en )
+			q <= d;
+endmodule
+
+module latchn
+    ( input d, clk, en, output reg q );
+	always @*
+		if ( !en )
+			q <= d;
+endmodule
+
+module latchsr
+    ( input d, clk, en, clr, pre, output reg q );
+	always @*
+		if ( clr )
+			q <= 1'b0;
+		else if ( pre )
+			q <= 1'b1;
+		else if ( en )
+			q <= d;
+endmodule

tests/ecp5/latches.ys

@@ -0,0 +1,35 @@
+
+read_verilog latches.v
+design -save read
+
+hierarchy -top latchp
+proc
+# Can't run any sort of equivalence check because latches are blown to LUTs
+synth_ecp5
+cd latchp # Constrain all select calls below inside the top module
+select -assert-count 1 t:LUT4
+
+select -assert-none t:LUT4 %% t:* %D
+
+
+design -load read
+hierarchy -top latchn
+proc
+# Can't run any sort of equivalence check because latches are blown to LUTs
+synth_ecp5
+cd latchn # Constrain all select calls below inside the top module
+select -assert-count 1 t:LUT4
+
+select -assert-none t:LUT4 %% t:* %D
+
+
+design -load read
+hierarchy -top latchsr
+proc
+# Can't run any sort of equivalence check because latches are blown to LUTs
+synth_ecp5
+cd latchsr # Constrain all select calls below inside the top module
+select -assert-count 2 t:LUT4
+select -assert-count 1 t:PFUMX
+
+select -assert-none t:LUT4 t:PFUMX %% t:* %D

tests/ecp5/logic.v

@@ -0,0 +1,18 @@
+module top
+(
+ input [0:7] in,
+ output B1,B2,B3,B4,B5,B6,B7,B8,B9,B10
+ );
+
+   assign     B1 =  in[0] & in[1];
+   assign     B2 =  in[0] | in[1];
+   assign     B3 =  in[0] ~& in[1];
+   assign     B4 =  in[0] ~| in[1];
+   assign     B5 =  in[0] ^ in[1];
+   assign     B6 =  in[0] ~^ in[1];
+   assign     B7 =  ~in[0];
+   assign     B8 =  in[0];
+   assign     B9 =  in[0:1] && in [2:3];
+   assign     B10 =  in[0:1] || in [2:3];
+
+endmodule

tests/ecp5/logic.ys

@@ -0,0 +1,8 @@
+read_verilog logic.v
+hierarchy -top top
+proc
+equiv_opt -assert -map +/ecp5/cells_sim.v synth_ecp5 # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd top # Constrain all select calls below inside the top module
+select -assert-count 9 t:LUT4
+select -assert-none t:LUT4 %% t:* %D

tests/ecp5/macc.v

@@ -0,0 +1,25 @@
+/*
+Example from: https://www.latticesemi.com/-/media/LatticeSemi/Documents/UserManuals/EI/iCEcube201701UserGuide.ashx?document_id=52071 [p. 77].
+*/
+module top(clk,a,b,c,set);
+parameter A_WIDTH = 4;
+parameter B_WIDTH = 3;
+input set;
+input clk;
+input signed [(A_WIDTH - 1):0] a;
+input signed [(B_WIDTH - 1):0] b;
+output signed [(A_WIDTH + B_WIDTH - 1):0] c;
+reg [(A_WIDTH + B_WIDTH - 1):0] reg_tmp_c;
+assign c = reg_tmp_c;
+always @(posedge clk)
+begin
+if(set)
+begin
+reg_tmp_c <= 0;
+end
+else
+begin
+reg_tmp_c <= a * b + c;
+end
+end
+endmodule

tests/ecp5/macc.ys

@@ -0,0 +1,13 @@
+read_verilog macc.v
+hierarchy -top top
+proc
+# Blocked by issue #1358 (Missing ECP5 simulation models)
+#equiv_opt -assert -map +/ecp5/cells_sim.v synth_ecp5 # equivalency check
+equiv_opt -map +/ecp5/cells_sim.v synth_ecp5 # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd top # Constrain all select calls below inside the top module
+select -assert-count 1 t:MULT18X18D
+select -assert-count 4 t:CCU2C
+select -assert-count 7 t:TRELLIS_FF
+
+select -assert-none t:CCU2C t:MULT18X18D t:TRELLIS_FF %% t:* %D

tests/ecp5/memory.v

@@ -0,0 +1,21 @@
+module top
+(
+	input [7:0] data_a,
+	input [6:1] addr_a,
+	input we_a, clk,
+	output reg [7:0] q_a
+);
+	// Declare the RAM variable
+	reg [7:0] ram[63:0];
+
+	// Port A
+	always @ (posedge clk)
+	begin
+		if (we_a)
+		begin
+			ram[addr_a] <= data_a;
+			q_a <= data_a;
+		end
+		q_a <= ram[addr_a];
+	end
+endmodule

tests/ecp5/memory.ys

@@ -0,0 +1,19 @@
+read_verilog memory.v
+hierarchy -top top
+proc
+memory -nomap
+equiv_opt -run :prove -map +/ecp5/cells_sim.v synth_ecp5
+memory
+opt -full
+
+miter -equiv -flatten -make_assert -make_outputs gold gate miter
+sat -verify -prove-asserts -seq 5 -set-init-zero -show-inputs -show-outputs miter
+
+design -load postopt
+cd top
+select -assert-count 24 t:L6MUX21
+select -assert-count 71 t:LUT4
+select -assert-count 32 t:PFUMX
+select -assert-count 8 t:TRELLIS_DPR16X4
+select -assert-count 35 t:TRELLIS_FF
+select -assert-none t:L6MUX21 t:LUT4 t:PFUMX t:TRELLIS_DPR16X4 t:TRELLIS_FF %% t:* %D

tests/ecp5/mul.v

@@ -0,0 +1,11 @@
+module top
+(
+ input [5:0] x,
+ input [5:0] y,
+
+ output [11:0] A,
+ );
+
+assign A =  x * y;
+
+endmodule

tests/ecp5/mul.ys

@@ -0,0 +1,11 @@
+read_verilog mul.v
+hierarchy -top top
+proc
+# Blocked by issue #1358 (Missing ECP5 simulation models)
+#equiv_opt -assert -map +/ecp5/cells_sim.v synth_ecp5 # equivalency check
+equiv_opt -map +/ecp5/cells_sim.v synth_ecp5 # equivalency check
+
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd top # Constrain all select calls below inside the top module
+select -assert-count 1 t:MULT18X18D
+select -assert-none t:MULT18X18D %% t:* %D

tests/ecp5/mux.v

@@ -0,0 +1,66 @@
+module mux2 (S,A,B,Y);
+    input S;
+    input A,B;
+    output reg Y;
+
+    always @(*)
+		Y = (S)? B : A;
+endmodule
+
+module mux4 ( S, D, Y );
+
+input[1:0] S;
+input[3:0] D;
+output Y;
+
+reg Y;
+wire[1:0] S;
+wire[3:0] D;
+
+always @*
+begin
+    case( S )
+       0 : Y = D[0];
+       1 : Y = D[1];
+       2 : Y = D[2];
+       3 : Y = D[3];
+   endcase
+end
+
+endmodule
+
+module mux8 ( S, D, Y );
+
+input[2:0] S;
+input[7:0] D;
+output Y;
+
+reg Y;
+wire[2:0] S;
+wire[7:0] D;
+
+always @*
+begin
+   case( S )
+       0 : Y = D[0];
+       1 : Y = D[1];
+       2 : Y = D[2];
+       3 : Y = D[3];
+       4 : Y = D[4];
+       5 : Y = D[5];
+       6 : Y = D[6];
+       7 : Y = D[7];
+   endcase
+end
+
+endmodule
+
+module mux16 (D, S, Y);
+ 	input  [15:0] D;
+ 	input  [3:0] S;
+ 	output Y;
+
+assign Y = D[S];
+
+endmodule
+

tests/ecp5/mux.ys

@@ -0,0 +1,46 @@
+read_verilog mux.v
+design -save read
+
+hierarchy -top mux2
+proc
+equiv_opt -assert -map +/ecp5/cells_sim.v synth_ecp5 # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd mux2 # Constrain all select calls below inside the top module
+select -assert-count 1 t:LUT4
+select -assert-none t:LUT4 %% t:* %D
+
+design -load read
+hierarchy -top mux4
+proc
+equiv_opt -assert -map +/ecp5/cells_sim.v synth_ecp5 # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd mux4 # Constrain all select calls below inside the top module
+select -assert-count 1 t:L6MUX21
+select -assert-count 4 t:LUT4
+select -assert-count 2 t:PFUMX
+
+select -assert-none t:LUT4 t:L6MUX21 t:PFUMX %% t:* %D
+
+design -load read
+hierarchy -top mux8
+proc
+equiv_opt -assert -map +/ecp5/cells_sim.v synth_ecp5 # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd mux8 # Constrain all select calls below inside the top module
+select -assert-count 1 t:L6MUX21
+select -assert-count 7 t:LUT4
+select -assert-count 2 t:PFUMX
+
+select -assert-none t:LUT4 t:L6MUX21 t:PFUMX %% t:* %D
+
+design -load read
+hierarchy -top mux16
+proc
+equiv_opt -assert -map +/ecp5/cells_sim.v synth_ecp5 # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd mux16 # Constrain all select calls below inside the top module
+select -assert-count 8 t:L6MUX21
+select -assert-count 26 t:LUT4
+select -assert-count 12 t:PFUMX
+
+select -assert-none t:LUT4 t:L6MUX21 t:PFUMX %% t:* %D

tests/ecp5/rom.v

@@ -0,0 +1,18 @@
+/*
+Example from: https://www.latticesemi.com/-/media/LatticeSemi/Documents/UserManuals/EI/iCEcube201701UserGuide.ashx?document_id=52071 [p. 74].
+*/
+module top(data, addr);
+output [3:0] data;
+input [4:0] addr;
+always @(addr) begin
+case (addr)
+0 : data = 'h4;
+1 : data = 'h9;
+2 : data = 'h1;
+15 : data = 'h8;
+16 : data = 'h1;
+17 : data = 'h0;
+default : data = 'h0;
+endcase
+end
+endmodule

tests/ecp5/rom.ys

@@ -0,0 +1,10 @@
+read_verilog rom.v
+hierarchy -top top
+proc
+flatten
+equiv_opt -assert -map +/ecp5/cells_sim.v synth_ecp5 # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd top # Constrain all select calls below inside the top module
+select -assert-count 6 t:LUT4
+select -assert-count 3 t:PFUMX
+select -assert-none t:LUT4 t:PFUMX %% t:* %D

tests/ecp5/run-test.sh

@@ -0,0 +1,20 @@
+#!/usr/bin/env bash
+set -e
+{
+echo "all::"
+for x in *.ys; do
+	echo "all:: run-$x"
+	echo "run-$x:"
+	echo "	@echo 'Running $x..'"
+	echo "	@../../yosys -ql ${x%.ys}.log -w 'Yosys has only limited support for tri-state logic at the moment.' $x"
+done
+for s in *.sh; do
+	if [ "$s" != "run-test.sh" ]; then
+		echo "all:: run-$s"
+		echo "run-$s:"
+		echo "	@echo 'Running $s..'"
+		echo "	@bash $s"
+	fi
+done
+} > run-test.mk
+exec ${MAKE:-make} -f run-test.mk

tests/ecp5/shifter.v

@@ -0,0 +1,16 @@
+module top    (
+out,
+clk,
+in
+);
+    output [7:0] out;
+    input signed clk, in;
+    reg signed [7:0] out = 0;
+
+    always @(posedge clk)
+	begin
+		out    <= out >> 1;
+		out[7] <= in;
+	end
+
+endmodule

tests/ecp5/shifter.ys

@@ -0,0 +1,10 @@
+read_verilog shifter.v
+hierarchy -top top
+proc
+flatten
+equiv_opt -assert -map +/ecp5/cells_sim.v synth_ecp5 # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd top # Constrain all select calls below inside the top module
+ 
+select -assert-count 8 t:TRELLIS_FF
+select -assert-none t:TRELLIS_FF %% t:* %D

tests/ecp5/tribuf.v

@@ -0,0 +1,8 @@
+module tristate (en, i, o);
+    input en;
+    input i;
+    output o;
+
+	assign o = en ? i : 1'bz;
+
+endmodule

tests/ecp5/tribuf.ys

@@ -0,0 +1,9 @@
+read_verilog tribuf.v
+hierarchy -top tristate
+proc
+flatten
+equiv_opt -assert -map +/ecp5/cells_sim.v -map +/simcells.v synth_ecp5 # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd tristate # Constrain all select calls below inside the top module
+select -assert-count 1 t:$_TBUF_
+select -assert-none t:$_TBUF_ %% t:* %D

tests/ice40/latches.ys

@@ -1,14 +1,11 @@
 read_verilog latches.v
-design -save read
 
 proc
-async2sync # converts latches to a 'sync' variant clocked by a 'super'-clock
 flatten
-synth_ice40
-equiv_opt -assert -map +/ice40/cells_sim.v synth_ice40 # equivalency check
-design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+# Can't run any sort of equivalence check because latches are blown to LUTs
+#equiv_opt -async2sync -assert -map +/ice40/cells_sim.v synth_ice40 # equivalency check
 
-design -load read
+#design -load preopt
 synth_ice40
 cd top
 select -assert-count 4 t:SB_LUT4

tests/ice40/wrapcarry.ys

@@ -0,0 +1,22 @@
+read_verilog <<EOT
+module top(input A, B, CI, output O, CO);
+	SB_CARRY carry (
+		.I0(A),
+		.I1(B),
+		.CI(CI),
+		.CO(CO)
+	);
+	SB_LUT4 #(
+		.LUT_INIT(16'b 0110_1001_1001_0110)
+	) adder (
+		.I0(1'b0),
+		.I1(A),
+		.I2(B),
+		.I3(1'b0),
+		.O(O)
+	);
+endmodule
+EOT
+
+ice40_wrapcarry
+select -assert-count 1 t:$__ICE40_CARRY_WRAPPER

tests/svtypes/.gitignore

@@ -0,0 +1,3 @@
+/*.log
+/*.out
+/run-test.mk

tests/svtypes/run-test.sh

@@ -0,0 +1,20 @@
+#!/usr/bin/env bash
+set -e
+{
+echo "all::"
+for x in *.ys; do
+	echo "all:: run-$x"
+	echo "run-$x:"
+	echo "	@echo 'Running $x..'"
+	echo "	@../../yosys -ql ${x%.ys}.log $x"
+done
+for x in *.sv; do
+	if [ ! -f "${x%.sv}.ys"  ]; then
+		echo "all:: check-$x"
+		echo "check-$x:"
+		echo "	@echo 'Checking $x..'"
+		echo "	@../../yosys -ql ${x%.sv}.log -p \"prep -top top; sat -verify -prove-asserts\" $x"
+	fi
+done
+} > run-test.mk
+exec ${MAKE:-make} -f run-test.mk

tests/svtypes/typedef_memory.sv

@@ -0,0 +1,10 @@
+module top(input [3:0] addr, wdata, input clk, wen, output reg [3:0] rdata);
+	typedef logic [3:0] ram16x4_t[0:15];
+
+	(ram16x4_t) mem;
+
+	always @(posedge clk) begin
+		if (wen) mem[addr] <= wdata;
+		rdata <= mem[addr];
+	end
+endmodule

tests/svtypes/typedef_memory.ys

@@ -0,0 +1,3 @@
+read_verilog -sv typedef_memory.sv
+prep -top top
+select -assert-count 1 t:$mem r:SIZE=16 %i r:WIDTH=4 %i

tests/svtypes/typedef_memory_2.sv

@@ -0,0 +1,10 @@
+module top(input [3:0] addr, wdata, input clk, wen, output reg [3:0] rdata);
+	typedef logic [3:0] nibble;
+
+	(nibble) mem[0:15];
+
+	always @(posedge clk) begin
+		if (wen) mem[addr] <= wdata;
+		rdata <= mem[addr];
+	end
+endmodule

tests/svtypes/typedef_memory_2.ys

@@ -0,0 +1,4 @@
+read_verilog -sv typedef_memory_2.sv
+prep -top top
+dump
+select -assert-count 1 t:$mem r:SIZE=16 %i r:WIDTH=4 %i

tests/svtypes/typedef_package.sv

@@ -0,0 +1,11 @@
+package pkg;
+	typedef logic [7:0] uint8_t;
+endpackage
+
+module top;
+
+	(* keep *) (pkg::uint8_t) a = 8'hAA;
+
+	always @* assert(a == 8'hAA);
+
+endmodule

tests/svtypes/typedef_param.sv

@@ -0,0 +1,22 @@
+`define STRINGIFY(x) `"x`"
+`define STATIC_ASSERT(x) if(!(x)) $error({"assert failed: ", `STRINGIFY(x)})
+
+module top;
+
+	typedef logic [1:0] uint2_t;
+	typedef logic signed [3:0] int4_t;
+	typedef logic signed [7:0] int8_t;
+	typedef (int8_t) char_t;
+
+	parameter (uint2_t) int2 = 2'b10;
+	localparam (int4_t) int4 = -1;
+	localparam (int8_t) int8 = int4;
+	localparam (char_t) ch = int8;
+
+
+	`STATIC_ASSERT(int2 == 2'b10);
+	`STATIC_ASSERT(int4 == 4'b1111);
+	`STATIC_ASSERT(int8 == 8'b11111111);
+	`STATIC_ASSERT(ch   == 8'b11111111);
+
+endmodule

tests/svtypes/typedef_scopes.sv

@@ -0,0 +1,23 @@
+
+typedef logic [3:0] outer_uint4_t;
+
+module top;
+
+	(outer_uint4_t) u4_i = 8'hA5;
+	always @(*) assert(u4_i == 4'h5);
+
+	typedef logic [3:0] inner_type;
+	(inner_type) inner_i1 = 8'h5A;
+	always @(*) assert(inner_i1 == 4'hA);
+
+	if (1) begin: genblock
+		typedef logic [7:0] inner_type;
+		(inner_type) inner_gb_i = 8'hA5;
+		always @(*) assert(inner_gb_i == 8'hA5);
+	end
+
+	(inner_type) inner_i2 = 8'h42;
+	always @(*) assert(inner_i2 == 4'h2);
+
+
+endmodule

tests/svtypes/typedef_simple.sv

@@ -0,0 +1,19 @@
+module top;
+
+	typedef logic [1:0] uint2_t;
+	typedef logic signed [3:0] int4_t;
+	typedef logic signed [7:0] int8_t;
+	typedef (int8_t) char_t;
+
+	(* keep *) (uint2_t) int2 = 2'b10;
+	(* keep *) (int4_t) int4 = -1;
+	(* keep *) (int8_t) int8 = int4;
+	(* keep *) (char_t) ch = int8;
+
+
+	always @* assert(int2 == 2'b10);
+	always @* assert(int4 == 4'b1111);
+	always @* assert(int8 == 8'b11111111);
+	always @* assert(ch   == 8'b11111111);
+
+endmodule

tests/various/peepopt.ys

@@ -131,8 +131,8 @@ EOT
 proc
 equiv_opt -assert peepopt
 design -load postopt
-select -assert-count 1 t:$dff r:WIDTH=5 %i
-select -assert-count 1 t:$mux r:WIDTH=5 %i
+select -assert-count 1 t:$dff r:WIDTH=4 %i
+select -assert-count 1 t:$mux r:WIDTH=4 %i
 select -assert-count 0 t:$dff t:$mux %% t:* %D
 
 ####################
@@ -173,3 +173,41 @@ select -assert-count 1 t:$dff r:WIDTH=2 %i
 select -assert-count 2 t:$mux
 select -assert-count 2 t:$mux r:WIDTH=2 %i
 select -assert-count 0 t:$logic_not t:$dff t:$mux %% t:* %D
+
+####################
+
+design -reset
+read_verilog <<EOT
+module peepopt_dffmuxext_signed_rst_init(input clk, ce, rstn, input signed [1:0] i, output reg signed [3:0] o);
+    initial o <= 4'b0010;
+    always @(posedge clk) begin
+        if (ce) o <= i;
+        if (!rstn) o <= 4'b1111;
+    end
+endmodule
+EOT
+
+proc
+# NB: equiv_opt uses equiv_induct which covers
+#     only the induction half of temporal induction
+#     --- missing the base-case half
+#     This makes it akin to `sat -tempinduct-inductonly`
+#     instead of `sat -tempinduct-baseonly` or
+#     `sat -tempinduct` which is necessary for this
+#     testcase
+#equiv_opt -assert peepopt
+
+design -save gold
+peepopt
+wreduce
+design -stash gate
+design -import gold -as gold
+design -import gate -as gate
+miter -equiv -flatten -make_assert -make_outputs gold gate miter
+sat -tempinduct -verify -prove-asserts -show-ports miter
+
+design -load gate
+select -assert-count 1 t:$dff r:WIDTH=4 %i
+select -assert-count 2 t:$mux
+select -assert-count 2 t:$mux r:WIDTH=4 %i
+select -assert-count 0 t:$logic_not t:$dff t:$mux %% t:* %D

tests/xilinx/.gitignore

@@ -2,3 +2,4 @@
 /*.out
 /run-test.mk
 /*_uut.v
+/test_macc

tests/xilinx/add_sub.v

@@ -0,0 +1,13 @@
+module top
+(
+ input [3:0] x,
+ input [3:0] y,
+
+ output [3:0] A,
+ output [3:0] B
+ );
+
+assign A =  x + y;
+assign B =  x - y;
+
+endmodule

tests/xilinx/add_sub.ys

@@ -0,0 +1,11 @@
+read_verilog add_sub.v
+hierarchy -top top
+proc
+equiv_opt -assert -map +/xilinx/cells_sim.v synth_xilinx # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd top # Constrain all select calls below inside the top module
+select -assert-count 14 t:LUT2
+select -assert-count 6 t:MUXCY
+select -assert-count 8 t:XORCY
+select -assert-none t:LUT2 t:MUXCY t:XORCY %% t:* %D
+

tests/xilinx/adffs.v

@@ -0,0 +1,47 @@
+module adff
+    ( input d, clk, clr, output reg q );
+    initial begin
+      q = 0;
+    end
+	always @( posedge clk, posedge clr )
+		if ( clr )
+			q <= 1'b0;
+		else
+            q <= d;
+endmodule
+
+module adffn
+    ( input d, clk, clr, output reg q );
+    initial begin
+      q = 0;
+    end
+	always @( posedge clk, negedge clr )
+		if ( !clr )
+			q <= 1'b0;
+		else
+            q <= d;
+endmodule
+
+module dffs
+    ( input d, clk, pre, clr, output reg q );
+    initial begin
+      q = 0;
+    end
+	always @( posedge clk )
+		if ( pre )
+			q <= 1'b1;
+		else
+            q <= d;
+endmodule
+
+module ndffnr
+    ( input d, clk, pre, clr, output reg q );
+    initial begin
+      q = 0;
+    end
+	always @( negedge clk )
+		if ( !clr )
+			q <= 1'b0;
+		else
+            q <= d;
+endmodule

tests/xilinx/adffs.ys

@@ -0,0 +1,51 @@
+read_verilog adffs.v
+design -save read
+
+hierarchy -top adff
+proc
+equiv_opt -async2sync  -assert -map +/xilinx/cells_sim.v synth_xilinx # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd adff # Constrain all select calls below inside the top module
+select -assert-count 1 t:BUFG
+select -assert-count 1 t:FDCE
+
+select -assert-none t:BUFG t:FDCE %% t:* %D
+
+
+design -load read
+hierarchy -top adffn
+proc
+equiv_opt -async2sync  -assert -map +/xilinx/cells_sim.v synth_xilinx # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd adffn # Constrain all select calls below inside the top module
+select -assert-count 1 t:BUFG
+select -assert-count 1 t:FDCE
+select -assert-count 1 t:LUT1
+
+select -assert-none t:BUFG t:FDCE t:LUT1 %% t:* %D
+
+
+design -load read
+hierarchy -top dffs
+proc
+equiv_opt -async2sync  -assert -map +/xilinx/cells_sim.v synth_xilinx # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd dffs # Constrain all select calls below inside the top module
+select -assert-count 1 t:BUFG
+select -assert-count 1 t:FDRE
+select -assert-count 1 t:LUT2
+
+select -assert-none t:BUFG t:FDRE t:LUT2 %% t:* %D
+
+
+design -load read
+hierarchy -top ndffnr
+proc
+equiv_opt -async2sync  -assert -map +/xilinx/cells_sim.v synth_xilinx # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd ndffnr # Constrain all select calls below inside the top module
+select -assert-count 1 t:BUFG
+select -assert-count 1 t:FDRE_1
+select -assert-count 1 t:LUT2
+
+select -assert-none t:BUFG t:FDRE_1 t:LUT2 %% t:* %D

tests/xilinx/counter.v

@@ -0,0 +1,17 @@
+module top    (
+out,
+clk,
+reset
+);
+    output [7:0] out;
+    input clk, reset;
+    reg [7:0] out;
+
+    always @(posedge clk, posedge reset)
+		if (reset) begin
+			out <= 8'b0 ;
+		end else
+			out <= out + 1;
+
+
+endmodule

tests/xilinx/counter.ys

@@ -0,0 +1,14 @@
+read_verilog counter.v
+hierarchy -top top
+proc
+flatten
+equiv_opt -async2sync -assert -map +/xilinx/cells_sim.v synth_xilinx # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd top # Constrain all select calls below inside the top module
+
+select -assert-count 1 t:BUFG
+select -assert-count 8 t:FDCE
+select -assert-count 1 t:LUT1
+select -assert-count 7 t:MUXCY
+select -assert-count 8 t:XORCY
+select -assert-none t:BUFG t:FDCE t:LUT1 t:MUXCY t:XORCY %% t:* %D

tests/xilinx/dffs.v

@@ -0,0 +1,15 @@
+module dff
+    ( input d, clk, output reg q );
+	always @( posedge clk )
+            q <= d;
+endmodule
+
+module dffe
+    ( input d, clk, en, output reg q );
+    initial begin
+      q = 0;
+    end
+	always @( posedge clk )
+		if ( en )
+			q <= d;
+endmodule

tests/xilinx/dffs.ys

@@ -0,0 +1,25 @@
+read_verilog dffs.v
+design -save read
+
+hierarchy -top dff
+proc
+equiv_opt -assert -map +/xilinx/cells_sim.v synth_xilinx # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd dff # Constrain all select calls below inside the top module
+select -assert-count 1 t:BUFG
+select -assert-count 1 t:FDRE
+
+select -assert-none t:BUFG t:FDRE %% t:* %D
+
+
+design -load read
+hierarchy -top dffe
+proc
+equiv_opt -assert -map +/xilinx/cells_sim.v synth_xilinx # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd dffe # Constrain all select calls below inside the top module
+select -assert-count 1 t:BUFG
+select -assert-count 1 t:FDRE
+
+select -assert-none t:BUFG t:FDRE %% t:* %D
+

tests/xilinx/fsm.v

@@ -0,0 +1,55 @@
+ module fsm (
+ clock,
+ reset,
+ req_0,
+ req_1,
+ gnt_0,
+ gnt_1
+ );
+ input   clock,reset,req_0,req_1;
+ output  gnt_0,gnt_1;
+ wire    clock,reset,req_0,req_1;
+ reg     gnt_0,gnt_1;
+
+ parameter SIZE = 3           ;
+ parameter IDLE  = 3'b001,GNT0 = 3'b010,GNT1 = 3'b100,GNT2 = 3'b101 ;
+
+ reg [SIZE-1:0] state;
+ reg [SIZE-1:0] next_state;
+
+ always @ (posedge clock)
+ begin : FSM
+ if (reset == 1'b1) begin
+   state <=  #1  IDLE;
+   gnt_0 <= 0;
+   gnt_1 <= 0;
+ end else
+  case(state)
+    IDLE : if (req_0 == 1'b1) begin
+                 state <=  #1  GNT0;
+                 gnt_0 <= 1;
+               end else if (req_1 == 1'b1) begin
+                 gnt_1 <= 1;
+                 state <=  #1  GNT0;
+               end else begin
+                 state <=  #1  IDLE;
+               end
+    GNT0 : if (req_0 == 1'b1) begin
+                 state <=  #1  GNT0;
+               end else begin
+                 gnt_0 <= 0;
+                 state <=  #1  IDLE;
+               end
+    GNT1 : if (req_1 == 1'b1) begin
+                 state <=  #1  GNT2;
+				 gnt_1 <= req_0;
+               end
+    GNT2 : if (req_0 == 1'b1) begin
+                 state <=  #1  GNT1;
+				 gnt_1 <= req_1;
+               end
+    default : state <=  #1  IDLE;
+ endcase
+ end
+
+endmodule

tests/xilinx/fsm.ys

@@ -0,0 +1,14 @@
+read_verilog fsm.v
+hierarchy -top fsm
+proc
+flatten
+equiv_opt -assert -map +/xilinx/cells_sim.v synth_xilinx # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd fsm # Constrain all select calls below inside the top module
+
+select -assert-count 1 t:BUFG
+select -assert-count 5 t:FDRE
+select -assert-count 1 t:LUT3
+select -assert-count 2 t:LUT4
+select -assert-count 4 t:LUT6
+select -assert-none t:BUFG t:FDRE t:LUT3 t:LUT4 t:LUT6 %% t:* %D

tests/xilinx/latches.v

@@ -1,19 +1,19 @@
 module latchp
-    ( input d, en, output reg q );
+    ( input d, clk, en, output reg q );
 	always @*
 		if ( en )
 			q <= d;
 endmodule
 
 module latchn
-    ( input d, en, output reg q );
+    ( input d, clk, en, output reg q );
 	always @*
 		if ( !en )
 			q <= d;
 endmodule
 
 module latchsr
-    ( input d, en, clr, pre, output reg q );
+    ( input d, clk, en, clr, pre, output reg q );
 	always @*
 		if ( clr )
 			q <= 1'b0;
@@ -22,37 +22,3 @@ module latchsr
 		else if ( en )
 			q <= d;
 endmodule
-
-
-module top (
-input clk,
-input clr,
-input pre,
-input a,
-output b,b1,b2
-);
-
-
-latchp u_latchp (
-        .en (clk ),
-        .d (a ),
-        .q (b )
-    );
-
-
-latchn u_latchn (
-        .en (clk ),
-        .d (a ),
-        .q (b1 )
-    );
-
-
-latchsr u_latchsr (
-        .en (clk ),
-        .clr (clr),
-        .pre (pre),
-        .d (a ),
-        .q (b2 )
-    );
-
-endmodule

tests/xilinx/latches.ys

@@ -1,15 +1,35 @@
 read_verilog latches.v
+design -save read
 
+hierarchy -top latchp
 proc
-flatten
-equiv_opt -assert -run :prove -map +/xilinx/cells_sim.v synth_xilinx # equivalency check
-async2sync
-equiv_opt -assert -run prove: -map +/xilinx/cells_sim.v synth_xilinx # equivalency check
+equiv_opt -async2sync -assert -map +/xilinx/cells_sim.v synth_xilinx # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd latchp # Constrain all select calls below inside the top module
+select -assert-count 1 t:LDCE
 
-design -load preopt
-synth_xilinx
-cd top
+select -assert-none t:LDCE %% t:* %D
+
+
+design -load read
+hierarchy -top latchn
+proc
+equiv_opt -async2sync -assert -map +/xilinx/cells_sim.v synth_xilinx # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd latchn # Constrain all select calls below inside the top module
+select -assert-count 1 t:LDCE
 select -assert-count 1 t:LUT1
+
+select -assert-none t:LDCE t:LUT1 %% t:* %D
+
+
+design -load read
+hierarchy -top latchsr
+proc
+equiv_opt -async2sync -assert -map +/xilinx/cells_sim.v synth_xilinx # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd latchsr # Constrain all select calls below inside the top module
+select -assert-count 1 t:LDCE
 select -assert-count 2 t:LUT3
-select -assert-count 3 t:LDCE
-select -assert-none t:LUT1 t:LUT3 t:LDCE %% t:* %D
+
+select -assert-none t:LDCE t:LUT3 %% t:* %D

tests/xilinx/logic.v

@@ -0,0 +1,18 @@
+module top
+(
+ input [0:7] in,
+ output B1,B2,B3,B4,B5,B6,B7,B8,B9,B10
+ );
+
+   assign     B1 =  in[0] & in[1];
+   assign     B2 =  in[0] | in[1];
+   assign     B3 =  in[0] ~& in[1];
+   assign     B4 =  in[0] ~| in[1];
+   assign     B5 =  in[0] ^ in[1];
+   assign     B6 =  in[0] ~^ in[1];
+   assign     B7 =  ~in[0];
+   assign     B8 =  in[0];
+   assign     B9 =  in[0:1] && in [2:3];
+   assign     B10 =  in[0:1] || in [2:3];
+
+endmodule

tests/xilinx/logic.ys

@@ -0,0 +1,11 @@
+read_verilog logic.v
+hierarchy -top top
+proc
+equiv_opt -assert -map +/xilinx/cells_sim.v synth_xilinx # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd top # Constrain all select calls below inside the top module
+
+select -assert-count 1 t:LUT1
+select -assert-count 6 t:LUT2
+select -assert-count 2 t:LUT4
+select -assert-none t:LUT1 t:LUT2 t:LUT4 %% t:* %D

tests/xilinx/macc.ys

@@ -1,8 +1,8 @@
 read_verilog macc.v
 design -save read
 
-proc
 hierarchy -top macc
+proc
 #equiv_opt -assert -map +/xilinx/cells_sim.v synth_xilinx ### TODO
 equiv_opt -run :prove -map +/xilinx/cells_sim.v synth_xilinx
 miter -equiv -flatten -make_assert -make_outputs gold gate miter
@@ -15,8 +15,8 @@ select -assert-count 1 t:DSP48E1
 select -assert-none t:BUFG t:FDRE t:DSP48E1 %% t:* %D
 
 design -load read
-proc
 hierarchy -top macc2
+proc
 #equiv_opt -assert -map +/xilinx/cells_sim.v synth_xilinx ### TODO
 equiv_opt -run :prove -map +/xilinx/cells_sim.v synth_xilinx
 miter -equiv -flatten -make_assert -make_outputs gold gate miter

tests/xilinx/memory.v

@@ -0,0 +1,21 @@
+module top
+(
+	input [7:0] data_a,
+	input [6:1] addr_a,
+	input we_a, clk,
+	output reg [7:0] q_a
+);
+	// Declare the RAM variable
+	reg [7:0] ram[63:0];
+
+	// Port A
+	always @ (posedge clk)
+	begin
+		if (we_a)
+		begin
+			ram[addr_a] <= data_a;
+			q_a <= data_a;
+		end
+		q_a <= ram[addr_a];
+	end
+endmodule

tests/xilinx/memory.ys

@@ -0,0 +1,17 @@
+read_verilog memory.v
+hierarchy -top top
+proc
+memory -nomap
+equiv_opt -run :prove -map +/xilinx/cells_sim.v synth_xilinx
+memory
+opt -full
+
+miter -equiv -flatten -make_assert -make_outputs gold gate miter
+sat -verify -prove-asserts -seq 5 -set-init-zero -show-inputs -show-outputs miter
+
+design -load postopt
+cd top
+select -assert-count 1 t:BUFG
+select -assert-count 8 t:FDRE
+select -assert-count 8 t:RAM64X1D
+select -assert-none t:BUFG t:FDRE t:RAM64X1D %% t:* %D

tests/xilinx/mul.v

@@ -0,0 +1,11 @@
+module top
+(
+ input [5:0] x,
+ input [5:0] y,
+
+ output [11:0] A,
+ );
+
+assign A =  x * y;
+
+endmodule

tests/xilinx/mul.ys

@@ -0,0 +1,9 @@
+read_verilog mul.v
+hierarchy -top top
+proc
+equiv_opt -assert -map +/xilinx/cells_sim.v synth_xilinx # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd top # Constrain all select calls below inside the top module
+
+select -assert-count 1 t:DSP48E1
+select -assert-none t:DSP48E1 %% t:* %D

tests/xilinx/mul_unsigned.ys

@@ -1,6 +1,7 @@
 read_verilog mul_unsigned.v
-proc
 hierarchy -top mul_unsigned
+proc
+
 equiv_opt -assert -map +/xilinx/cells_sim.v synth_xilinx # equivalency check
 design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
 cd mul_unsigned # Constrain all select calls below inside the top module

tests/xilinx/mux.v

@@ -0,0 +1,65 @@
+module mux2 (S,A,B,Y);
+    input S;
+    input A,B;
+    output reg Y;
+
+    always @(*)
+		Y = (S)? B : A;
+endmodule
+
+module mux4 ( S, D, Y );
+
+input[1:0] S;
+input[3:0] D;
+output Y;
+
+reg Y;
+wire[1:0] S;
+wire[3:0] D;
+
+always @*
+begin
+    case( S )
+       0 : Y = D[0];
+       1 : Y = D[1];
+       2 : Y = D[2];
+       3 : Y = D[3];
+   endcase
+end
+
+endmodule
+
+module mux8 ( S, D, Y );
+
+input[2:0] S;
+input[7:0] D;
+output Y;
+
+reg Y;
+wire[2:0] S;
+wire[7:0] D;
+
+always @*
+begin
+   case( S )
+       0 : Y = D[0];
+       1 : Y = D[1];
+       2 : Y = D[2];
+       3 : Y = D[3];
+       4 : Y = D[4];
+       5 : Y = D[5];
+       6 : Y = D[6];
+       7 : Y = D[7];
+   endcase
+end
+
+endmodule
+
+module mux16 (D, S, Y);
+ 	input  [15:0] D;
+ 	input  [3:0] S;
+ 	output Y;
+
+assign Y = D[S];
+
+endmodule

tests/xilinx/mux.ys

@@ -0,0 +1,45 @@
+read_verilog mux.v
+design -save read
+
+hierarchy -top mux2
+proc
+equiv_opt -assert -map +/xilinx/cells_sim.v synth_xilinx # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd mux2 # Constrain all select calls below inside the top module
+select -assert-count 1 t:LUT3
+
+select -assert-none t:LUT3 %% t:* %D
+
+
+design -load read
+hierarchy -top mux4
+proc
+equiv_opt -assert -map +/xilinx/cells_sim.v synth_xilinx # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd mux4 # Constrain all select calls below inside the top module
+select -assert-count 1 t:LUT6
+
+select -assert-none t:LUT6 %% t:* %D
+
+
+design -load read
+hierarchy -top mux8
+proc
+equiv_opt -assert -map +/xilinx/cells_sim.v synth_xilinx # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd mux8 # Constrain all select calls below inside the top module
+select -assert-count 1 t:LUT3
+select -assert-count 2 t:LUT6
+
+select -assert-none t:LUT3 t:LUT6 %% t:* %D
+
+
+design -load read
+hierarchy -top mux16
+proc
+equiv_opt -assert -map +/xilinx/cells_sim.v synth_xilinx # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd mux16 # Constrain all select calls below inside the top module
+select -assert-count 5 t:LUT6
+
+select -assert-none t:LUT6 %% t:* %D

tests/xilinx/run-test.sh

@@ -6,7 +6,7 @@ for x in *.ys; do
 	echo "all:: run-$x"
 	echo "run-$x:"
 	echo "	@echo 'Running $x..'"
-	echo "	@../../yosys -ql ${x%.ys}.log $x"
+	echo "	@../../yosys -ql ${x%.ys}.log -w 'Yosys has only limited support for tri-state logic at the moment.' $x"
 done
 for s in *.sh; do
 	if [ "$s" != "run-test.sh" ]; then

tests/xilinx/shifter.v

@@ -0,0 +1,16 @@
+module top    (
+out,
+clk,
+in
+);
+    output [7:0] out;
+    input signed clk, in;
+    reg signed [7:0] out = 0;
+
+    always @(posedge clk)
+	begin
+		out    <= out >> 1;
+		out[7] <= in;
+	end
+
+endmodule

tests/xilinx/shifter.ys

@@ -0,0 +1,11 @@
+read_verilog shifter.v
+hierarchy -top top
+proc
+flatten
+equiv_opt -assert -map +/xilinx/cells_sim.v synth_xilinx # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd top # Constrain all select calls below inside the top module
+
+select -assert-count 1 t:BUFG
+select -assert-count 8 t:FDRE
+select -assert-none t:BUFG t:FDRE %% t:* %D

tests/xilinx/tribuf.v

@@ -0,0 +1,8 @@
+module tristate (en, i, o);
+    input en;
+    input i;
+    output reg o;
+    
+    always @(en or i)
+		o <= (en)? i : 1'bZ;
+endmodule

tests/xilinx/tribuf.ys

@@ -0,0 +1,12 @@
+read_verilog tribuf.v
+hierarchy -top tristate
+proc
+tribuf
+flatten
+synth
+equiv_opt -assert -map +/xilinx/cells_sim.v -map +/simcells.v synth_xilinx # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd tristate # Constrain all select calls below inside the top module
+# TODO :: Tristate logic not yet supported; see https://github.com/YosysHQ/yosys/issues/1225
+select -assert-count 1 t:$_TBUF_
+select -assert-none t:$_TBUF_ %% t:* %D